tag:blogger.com,1999:blog-8639215628525378898.post1478620855195893489..comments2023-09-20T15:32:40.483+01:00Comments on Reprap development and further adventures in DIY 3D printing: Skeinforge Version 41RichRap3Dhttp://www.blogger.com/profile/09348596756294999378noreply@blogger.comBlogger10125tag:blogger.com,1999:blog-8639215628525378898.post-28729280385938234222012-08-19T13:34:01.705+01:002012-08-19T13:34:01.705+01:00http://www.thingiverse.com/thing:5504http://www.thingiverse.com/thing:5504Luca Martinellihttps://www.blogger.com/profile/06789502247794804889noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-67640413142722534202012-06-06T03:16:55.889+01:002012-06-06T03:16:55.889+01:00Where can I find that infinity sculpture below the...Where can I find that infinity sculpture below the Pyramid and the above the DNA?Anonymoushttps://www.blogger.com/profile/13224457290996697840noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-23066174859045553512012-04-03T15:50:25.455+01:002012-04-03T15:50:25.455+01:00I don't have one to hand, from memory, you jus...I don't have one to hand, from memory, you just need to set the enable pin (low/Gnd if I remember) and set the direction pin high or low (+5V)and then just use a button to clock in a pulse for the data pin, use a pull-up resistor 10k on the data pin and put the button between data and ground to simulate a low going pulse.<br />Press the button and your motor will turn in full steps by default.RichRap3Dhttps://www.blogger.com/profile/09348596756294999378noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-4300739125417623652012-03-27T13:41:14.755+01:002012-03-27T13:41:14.755+01:00Great post Rich,
I am getting closer to my first ...Great post Rich,<br /><br />I am getting closer to my first print each day and reading everything on repraps before i start.<br /><br />Your posts are well written and informative.<br />I am interested in your test circuit on your wishboard.<br /><br />I would like to test run my steppers when i wire them up. Do you have a link or schematic for the test run setup?<br /><br />Love your multicolored prints. That is something I have to try.Gregtedhttps://www.blogger.com/profile/12165934534912802029noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-76544787455224516112011-07-13T21:38:04.343+01:002011-07-13T21:38:04.343+01:00This comment has been removed by the author.Maxhttps://www.blogger.com/profile/17536918914535623255noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-2375529166877127392011-06-09T22:59:07.803+01:002011-06-09T22:59:07.803+01:00Thanks Pablo2M, I hope it's useful and I'm...Thanks Pablo2M, I hope it's useful and I'm glad you liked it.RichRap3Dhttps://www.blogger.com/profile/09348596756294999378noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-50397761812757828572011-06-09T22:47:59.564+01:002011-06-09T22:47:59.564+01:00Good guess Triffid Hunter, but Sublime got it spot...Good guess Triffid Hunter, but Sublime got it spot on, it's the pink panther girl. And Thanks Sublime you already worked out my next problem, I was starting to think Skeinforge had a bug, but it must be the model as it's always the same layers that have dodgy infill however I sliced it.<br />I'll send you a PM, thanks.RichRap3Dhttps://www.blogger.com/profile/09348596756294999378noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-26295795922612257392011-06-09T19:26:23.477+01:002011-06-09T19:26:23.477+01:00Great Post !Great Post !Anonymoushttps://www.blogger.com/profile/15329689454828893101noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-70739120244322888162011-06-09T19:04:40.752+01:002011-06-09T19:04:40.752+01:00Its the Pink panther girl and I have a hollowed ou...Its the Pink panther girl and I have a hollowed out version to solve the problem with skeinforges slicing. I would upload it but the original poster on Thingiverse posted his as all rights reserved even though the creator of the model apparently designed it with a less restrictive license. Contact me through the RepRap forums and I will email it to you.Sublimehttps://www.blogger.com/profile/17981768588609934835noreply@blogger.comtag:blogger.com,1999:blog-8639215628525378898.post-55299666090399922942011-06-09T16:06:06.774+01:002011-06-09T16:06:06.774+01:00http://www.thingiverse.com/thing:4895 ?
That pyra...http://www.thingiverse.com/thing:4895 ?<br /><br />That pyramid looks like an excellent calibration pieceTriffid Hunterhttps://www.blogger.com/profile/11285832141131462463noreply@blogger.com